[five_sixth_last]

Minwax® PolyShades® enhances wood grain by combining beautiful rich stain color and long-lasting polyurethane protection in one easy step.

  • It can also be used over polyurethane finishes, so you can change the color of your finished wood, without removing the existing finish.
  • To learn how PolyShades® can help you easily change the color of your stained or polyurethane finished wood, view the PolyShades® Color Transformation Guide.
  • *Minwax® PolyShades® is also available in an aerosol can.

[/five_sixth_last]

Minwax® PolyShades® 275 VOC Compliant will reduce finishing time as compared with staining with one product and protecting with another.

  • provides rich wood color and long lasting polyurethane protection, while enhancing the wood grain, in one simple step.

[tabs]

[tab title=”Product Details”]

Sheens: satin and gloss
Application Tool: high-quality natural bristle brush
Location: interior wood surfaces
Recoat: after 6 hours
Dry Time: 6 hours
Cleanup: mineral spirits
Coverage: 11 – 14 sq.m. per litr.
Coats: 2 coats are recommended. To deepen the color, apply a third coat.
Recommended Uses: furniture, woodwork, doors, cabinets, accessories

[/tab]
[tab title=”Surface Preparation:”]

NOT FOR USE ON FLOORS

  1. Before starting, surface must be dry, clean and free of dirt, grease and glue.
  2. Sand the wood in the direction of the grain using fine-grade sandpaper (#220) until smooth.
  3. Remove all sanding dust.
  4. To help ensure uniform acceptance of stain color and beautiful results, pretreat new or raw wood with oil-based Minwax® Pre-Stain Wood Conditioner, following label directions.

[/tab]
[tab title=”Application:”]

 

    1. Stir Minwax® PolyShades® thoroughly before and occasionally during use. Do not thin.
    2. Always test stain on a scrap piece or hidden area of wood to verify desired color.
    3. Using a natural bristle brush, dip approximately an inch into the can, gently tapping it against the inside to remove any excess. Apply a very THIN, even coat following the direction of the grain. Make sure to maintain a “wet” edge.
    4. To minimize the brush marks and bubbles after staining, tip off the surface by holding the brush at a 45 degree angle and lightly run the bristles over the entire length of the wood.
    5. Let the first coat dry for 6 hours or more. Dry time may be extended due to high humidity, low temperatures, and inadequate ventilation or if the coat is applied too thick.

Rub the surface lightly with fine steel wool (grade 000 or finer). Remove all dust. Brush on a second thin coat following directions above. To deepen the color, apply a third coat.

[/tab]
[tab title=”GHS SDS”]

Polyshades 275 V.O.C Satynowy Miodowy Klon
Polyshades 275 V.O.C Błyszczący Amerykański Kasztan
Polyshades 275 V.O.C Błyszczący Czarny
Polyshades 275 V.O.C Błyszczący Omszony Dąb
Polyshades 275 V.O.C Błyszczący Dojrzały Orzech Włoski
Polyshades 275 V.O.C Błyszczący Wyrazisty Mahoń
Polyshades 275 V.O.C Błyszczący Klasyczny Dąb
Polyshades 275 V.O.C Błyszczący Miodowy Klon
Polyshades 275 V.O.C Błyszczący Wiśnia
Polyshades 275 V.O.C Błyszczący Stary Klon
Polyshades 275 V.O.C Błyszczący Orzech Pekan
Polyshades Aerozol Błyszczący Dojrzały Orzech Włoski
Polyshades Aerozol Błyszczący Wyrazisty Mahoń
Polyshades Aerozol Błyszczący Czarny
Polyshades Aerozol Błyszczący Klasyczny Dąb
Polyshades Aerozol Błyszczący Omszony Dąb
Polyshades Aerozol Błyszczący Orzech Pekan
Polyshades Błyszczący Amerykański Kasztan
Polyshades Błyszczący Dojrzały Orzech Włoski
Polyshades Błyszczący Wyrazisty Mahoń
Polyshades Błyszczący Czarny
Polyshades Błyszczący Klasyczny Dąb
Polyshades Błyszczący Miodowy Klon
Polyshades Błyszczący Omszony Dąb
Polyshades Błyszczący Wiśnia
Polyshades Błyszczący Stary Klon
Polyshades Błyszczący Orzech Pekan
Polyshades Błyszczący Królewski Orzech
Polyshades Błyszczący Tudor
Polyshades 275 V.O.C Satynowy Amerykański Kasztan
Polyshades 275 V.O.C Satynowy Czarny
Polyshades 275 V.O.C Satynowy Omszony Dąb
Polyshades 275 V.O.C Satynowy Dojrzały Orzech Włoski
Polyshades 275 V.O.C Satynowy Wyrazisty Mahoń
Polyshades 275 V.O.C Satynowy Klasyczny Dąb
Polyshades 275 V.O.C Satynowy Wiśnia
Polyshades 275 V.O.C Satynowy Stary Klon
Polyshades 275 V.O.C Satynowy Orzech Pekan
Polyshades Aerozol Satynowy Dojrzały Orzech Włoski
Polyshades Aerozol Satynowy Wyrazisty Mahoń
Polyshades Aerozol Satynowy Czarny
Polyshades Aerozol Satynowy Klasyczny Dąb
Polyshades Aerozol Satynowy Omszony Dąb
Polyshades Aerozol Satynowy Orzech Pekan
Polyshades Satynowy Amerykański Kasztan
Polyshades Satynowy Dojrzały Orzech Włoski
Polyshades Satynowy Wyrazisty Mahoń
Polyshades Satynowy Czarny
Polyshades Satynowy Klasyczny Dąb
Polyshades Satynowy Miodowy Klon
Polyshades Satynowy Omszony Dąb
Polyshades Satynowy Wiśnia
Polyshades Satynowy Stary Klon
Polyshades Satynowy Orzech Pekan
Polyshades Satynowy Królewski Orzech
Polyshades Satynowy Tudor
Polyshades 275 V.O.C Błyszczący Espresso
Polyshades 450 V.O.C Błyszczący Espresso
Polyshades 275 V.O.C Satynowy Espresso
Polyshades 450 V.O.C Satynowy Espresso

[/tab]
[/tabs]

[toggle title=”Pytania i”]

Q:What is the advantage of PolyShades®?

PolyShades® combines stain for rich beautiful color with polyurethane for tough protection in one product. It is an ideal choice for those who want to save the time involved in staining with one product and protecting with another.

Q:Should Minwax® Pre-Stain Wood Conditioner be used as a pretreatment prior to PolyShades®?

Yes, if the wood being stained is soft or porous. Soft or porous woods, such as pine or aspen, tend to absorb stain unevenly. Before using PolyShades® on soft or porous woods, Minwax® Pre-Stain Wood Conditioner should be applied to ensure even stain penetration.

Q:Can PolyShades® be applied over an existing finish?

Yes, as long as the previous finish is not lacquer or shellac. Be sure to test the selected color on a hidden spot to see how it will look over the original finish. To prepare the surface, make sure that the finish is clean and has had all wax and polish removed. Then lightly sand with #180 or #220 sandpaper. The surface is then ready to be coated with PolyShades®.

Q:Can Minwax® Fast-Drying Polyurethane or Wipe-On Poly be applied over PolyShades®?

Yes. Since PolyShades® contains polyurethane, additional protection, without added color, can be provided with a clear coat of Minwax® Fast-Drying Polyurethane or Wipe-On Poly over the last coat of PolyShades®.

Q:Can PolyShades® be used on floors?

PolyShades® is not recommended for use on floors. Instead, stain with Minwax® Wood Finish™ and topcoat with Minwax® Super Fast-Drying Polyurethane for Floors or Minwax® Fast-Drying Polyurethane.

 

[/toggle]

[button size=”medium” align=”center” full=”true” link=”https://minwax.pl/kategorie-produktow/?product_cat=bejcowanie-i-wykonczenie-w-jednym-kroku&dppage=1/” linkTarget=”_blank” color=”green” hoverBgColor=”rgba(255,202,0,1)”]Chcesz kupić ten produkt? Kliknij tutaj. Zapraszamy do sklepu internetowego.[/button]