lakier, politura, szelak, lakier do drewna, lakier do metalu, szybkoschnący[five_sixth_last]

Minwax® Clear Brushing Lacquer is a clear, protective finish for wood and metal.

  • Dries to the touch in 30 minutes, ensuring a smooth, dust-free finish.
  • Requires no sanding between coats.
  • Great for woodwork, cabinets, furniture, doors, accessories

Also in aerosol.

[tabs]
[tab title=”Product Details”]

Sheens: gloss, semi-gloss, satin
Application Tool: high quality natural bristle brush
Location: interior wood surfaces
Recoat: dry to touch in 30 minutes; recoat after 2 hours
Dry Time: 30 minutes, 24 hours before normal use
Cleanup: lacquer thinner
Coverage: 11 sq.m. per litr.
Coats: 3
Recommended Uses: woodwork, cabinets, furniture, interior doors, accessories, not recommended for floors

[/tab]
[tab title=”Directions”]

  1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter. Note: Do not apply lacquer over polyurethane finishes.
  2. Sand to obtain a smooth, uniform surface. Remove all dust with a cloth dampened with mineral spirits.
  3. Apply Minwax® Wood Finish™ stain or Minwax® Lacquer Sanding Sealer, if desired, following label directions.
  4. Stir Minwax® Clear Brushing Lacquer well before and during use to rotate the product from the bottom to the top of the can. NEVER SHAKE.
  5. Apply a coat of lacquer using a high quality natural bristle brush. On unfinished wood, apply sufficient lacquer to seal open joints, edges and end grain.
  6. Let dry at least two hours, then apply a second coat.
  7. Apply a third coat, repeating the steps above for each coat. Apply a fourth coat, if desired.
  8. After final coat, allow at least 24 hours before normal use.

[notice]Note: For brush application only. Above dry times and coverage rates are based on good ventilation, temperature of 25° C and 50% relative humidity. Lower temperature, higher humidity, lack of ventilation or application of thick coats will extend dry time. Always test tackiness between coats. Do not recoat if surface is still tacky. Slight ambering may be experienced when lacquer is applied over light-colored stains or wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results. Minwax® Clear Brushing Lacquer is not recommended for use on floors. To protect floors, use Minwax® Super Fast-Drying Polyurethane for Floors or Minwax® Water Based Oil-Modified Polyurethane.[/notice]

[/tab]
[tab title=”Aerozol Directions”]

  1. Surface must be dry and free of old finished in poor condition, paint, wax, grease, polish, dirt or other foreign matter. Note: Do not apply lacquer over polyurethane finishes.
  2. Sand the wood to obtain a smooth, uniform surface. Remove all dust with cloth dampened with mineral spirits.
  3. Apply Minwax® Wood Finish™ stain or Minwax® Lacquer Sanding Sealer, if desired, following label directions.
  4. Shake the can of Minwax® Clear Brushing Lacquer vigorously for two minutes. Shake for 10 seconds occasionally during use.
  5. Protect adjacent areas from overspray. Wet overspray can be removed with lacquer thinner.
  6. Hold can vertically 12 inches from surface. Depress button fully and spray using an even, sweeping motion with slightly overlapping strokes. Spray several thin coats at the first spraying. On unfinished wood, apply sufficient material to seal open joins, edges and end-grain.
  7. Recoat after 30 minutes.
  8. Apply at least three coats.
  9. After final coat, allow at least 24 hours before normal use.

[info]CLEANUP: For easy clean-up, use lacquer thinner following the manufacturer’s safety instructions..

COVERAGE: About 11 sq.m. per litr.[/info]

[/tab]
[tab title=”Nozzle care”]

  1. Immediately after using, turn can upside down and depress nozzle until no liquid comes out.
  2. If nozzle is clogged, pull from can and clean with lacquer thinner. Do not stick pins or wire into can opening.

[info]CLEANUP: For easy clean-up, use lacquer thinner following the manufacturer’s safety instructions..[/info]

[/tab]
[tab title=”GHS SDS”]
Minwax Clear Brushing Lacquer Aerozol Bezbarwny Błyszczący
Minwax Clear Brushing Lacquer Aerozol Bezbarwny Półbłyszczący
Minwax Clear Brushing Lacquer Aerozol Bezbarwny Satynowy
Minwax Clear Brushing Lacquer Bezbarwny Błyszczący
Minwax Clear Brushing Lacquer Bezbarwny Półbłyszczący
Minwax Clear Brushing Lacquer Bezbarwny Satynowy

[/tab]
[/tabs]

[toggle title=”FAQs“]

Q:Does Minwax® Clear Brushing Lacquer require sanding between coats?

No. Since one coat melts into prior coats, there is no need to sand for adhesion. Also, since each coat dries to the touch in 30 minutes or less, there is less time for dust and debris to fall into the wet coating.

Q:Can Minwax® Clear Brushing Lacquer be used on floors?

No. Brushing Lacquer is not recommended for use on floors. Instead use Minwax® Fast-Drying Polyurethane or Minwax® Super Fast-Drying Polyurethane For Floors.

Q:Can Minwax® Clear Brushing Lacquer and Minwax® Lacquer Sanding Sealer be used over Minwax® stains?

Yes. Minwax® Clear Brushing Lacquer and Minwax® Lacquer Sanding Sealer can be applied over Minwax® Wood Finish™, Minwax® Water Based Wood Stains and Minwax® Gel Stains. If Lacquer Sanding Sealer is applied over stain, it is important not to sand too aggressively. Sanding through the sealer to the stain can damage the color.

Q: Can Minwax® Clear Brushing Lacquer be used in commercial spraying equipment?

No. Brushing Lacquer is specifically formulated to deliver excellent results when applied with a brush. It is not suitable for use in spray equipment. Minwax® Clear Aerosol Lacquer can be used on furniture, spindles and other projects where the convenience of an aerosol spray is desired.

Q:Can lacquer be used over polyurethane? Can polyurethane be used over lacquer?

No and no. Polyurethanes and lacquers are not compatible with each other. Applying one over the other may cause problems with adhesion.

Q:Does Minwax® Clear Brushing Lacquer change the color of the wood?

No. Unlike polyurethanes, which can amber over time, Brushing Lacquer remains clear.

Q:What type of applicator works best with Minwax® Clear Brushing Lacquer and Sanding Sealer?

Brushing lacquers work best with natural bristle brush. When choosing an applicator, the most important factor is selecting a high quality brush with tapered bristles that will enable you to “flow” the lacquer onto the wood. Avoid over-brushing, which can leave brush marks in the dried film. Do not use a foam brush, since it will dissolve!

 

[/toggle]

[error]WARNING[/error]
[error_msg]

DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.

CONFORMS TO ASTM D-4236. Contact a physician for more health information.

 

[/error_msg]

[button size=”medium” align=”center” full=”true” link=”https://minwax.pl/kategorie-produktow/?product_cat=lakiery&dppage=1/” linkTarget=”_blank” color=”green” hoverBgColor=”rgba(255,202,0,1)”]Chcesz kupić ten produkt? Kliknij tutaj. Zapraszamy do sklepu internetowego.[/button]